Latest revision as of 12:21, 5 January 2022

Purpose

I would like to unleash the power of my Ender 5 Plus(here after referenced as E5+) by removing the "bottleneck" that the weak mainboard processing power introduce. I also need to keep the cost as low as possible. Klipper supposedly should do just this, by moving all data processing from the E5+ mainboard on to the Raspberry Pi 4 i got connected already anyway.

First try/step will be a combo of Klipper and Octoprint. This makes it easy to flash the Klipper firmware onth the E5+ and I already got OctoPrint running at a Raspberry Pi 4 connected to my E5+ so...

Later i might try the Klipper + Moonraker + MainSail combo.

Klipper + OctoPrint

An installation guide is avilable on the Klipper website. I will follow that now.

make menuconfig will ask for microcontroller - the E5+ uses atmega2560. See printer-creality-ender5plus-2019.cfg

You(and I) MUST read, understand and perform the Config checks - Manual Leveling - Probe Calibration & Bed Leveling BEFORE trying to print!!

The overview page is a valuable resource of information so i got a lot of reading to do ;-)

Depending on the result of the first Benchy test print I believe that the next tuning should be done in this order:

Resonance compensation: A tool to reduce ringing in prints. This was a challenge to my 50 year old eyes but it actuallt helped a lot so do not skip this - find a magnifying glass ;-)
Calibrate Klipper extruder rotation_distance - I skipped this because the test prints didn't show _any_ signs of over- or under-extrution.
Extruder nozzle temperature - I skipped this because i already know what temperature the PLA i use need to be printed at on my E5+
Pressure advance: Calibrate extruder pressure.

Problems I ran into

The touch display on the printer does not work with Klipper and some search results suggests that the display on E5+ is not supported by Klipper :-/... i will keep look for solutions, but it is not essential to me because I use the OctoPrint webinterface. The stock 4.3 inch TFT LCD display is marked "DMT48270C043_06WT". Maybe that can help in the searce for solutions.

 THIS FIXED THE DISPLAY --> https://www.reddit.com/r/ender5plus/comments/kx9hsy/klipper_screen_on_ender_5_plus/

OctoPrint reported errors in the Gcode that turned out beeing related to hidden ascii codes in the start_gcode. Solution was found somewhere on the Intarwebs i cannot recall. I copied the Start and End G-code from Cura int Notepad++ and manually replaced all spaces with new ones. I could not see any difference on the spaces before and after BUT it worked so who cares ;-)
I lost http and ssh connection to the Raspberry Pi 3/4 into the Pressure Advance cube test print. The test print finished anyway so it was only network connections that died. I powercycled the Pi and everything seemed okay again!? It happened again and i suspect it is the WiFi connection that somehow locks up so I disabled the WiFi interface and connected the Raspberry Pi with an ethernet cable.

Reference pages

My cry for help in the Danish Facebook group Den seriøse Ender-3/Ender-5 gruppe
Klipper is a 3d-Printer firmware. It combines the power of a general purpose computer with one or more micro-controllers.
OctoPrint provides a snappy web interface for controlling consumer 3D printers.
Moonraker is a Python 3 based web server that exposes APIs with which client applications may use to interact with Klipper.
Mainsail is a lightweight & responsive web interface for the Klipper 3D printer firmware.
This document describe the G-Code commands that Klipper supports.
Printer.cfg reference.
My Printer.cfg file as of 5. jan. 2022

Notes for the future

During Probe calibration it may be necessary to set the printer’s Z position_min to a negative number (eg, position_min = -2).
Adjusting bed leveling screws is nessesary to do now and then ;-)
Calibrating PID settings is a wise thing to do everytime the environment around the printer changes 'significantly'.
Calibrate Klipper extruder rotation_distance.
Pressure advance: Calibrate extruder pressure. !!! Disable any PA setting already present in your config file before you run the PA test !!!
Resonance compensation
ALWAYS slice as described in the tips for configuring a “slicer” application for use with Klipper.

@@ Line 1: / Line 1: @@
 [[Category:Klipper]][[Category:3D Print]][[Category:Creality]][[Category:Ender 5 Plus]][[Category:RaspBerry Pi]][[Category:OctoPrint]]<span style="float:right;">__TOC__</span>
 = Purpose =
-I would like to unleash the power of my Ender 5 Plus(here after referenced as E5+) by removing the "bottleneck" that the weak mainboard processing power have.
+I would like to unleash the power of my Ender 5 Plus(here after referenced as E5+) by removing the "bottleneck" that the weak mainboard processing power introduce.
-Klipper supposedly should do just this by moving all data processing from the E5+ mainboard on to the Raspberry Pi 4 i got connected already anyway.
+I also need to keep the cost as low as possible.
+Klipper supposedly should do just this, by moving all data processing from the E5+ mainboard on to the Raspberry Pi 4 i got connected already anyway.
-First try/step will be a combo of Klipper and OctoPrint.
+First try/step will be a combo of [[#Klipper + OctoPrint combo|Klipper and Octoprint]]. This makes it easy to flash the Klipper firmware onth the E5+ and I already got OctoPrint running at a Raspberry Pi 4 connected to my E5+ so...
-Later i might try the Klipper + Moonraker + MainSail combo.
+Later i might try the [[#Klipper + Moonraker + MainSail combo|Klipper + Moonraker + MainSail combo]].
-= Klipper + OctoPrint combo =
+= Klipper + OctoPrint =
 An [https://www.klipper3d.org/Installation.html installation guide] is avilable on the Klipper website. I will follow that now.
 ''make menuconfig'' will ask for microcontroller - the E5+ uses ''atmega2560''. See [https://github.com/KevinOConnor/klipper/blob/master/config/printer-creality-ender5plus-2019.cfg printer-creality-ender5plus-2019.cfg]
-  You(and I) MUST read, understand and perform the [https://www.klipper3d.org/Config_checks.html Config checks] - [https://www.klipper3d.org/Manual_Level.html Manual Leveling] - [https://www.klipper3d.org/Probe_Calibrate.html Probe Calibration] & [https://www.klipper3d.org/Bed_Level.html Bed Leveling] BEFORE you try to print!!
+  You(and I) MUST read, understand and perform the [https://www.klipper3d.org/Config_checks.html Config checks] - [https://www.klipper3d.org/Manual_Level.html Manual Leveling] - [https://www.klipper3d.org/Probe_Calibrate.html Probe Calibration] & [https://www.klipper3d.org/Bed_Level.html Bed Leveling] BEFORE trying to print!!
 The [https://www.klipper3d.org/Overview.html overview page] is a valuable resource of information so i got a lot of reading to do ;-)
 Depending on the result of the first [http://www.3dbenchy.com/ Benchy] test print I believe that the next tuning should be done in this order:
-# [https://www.klipper3d.org/Resonance_Compensation.html Resonance compensation]: A tool to reduce ringing in prints.
+# [https://www.klipper3d.org/Resonance_Compensation.html Resonance compensation]: A tool to reduce ringing in prints. This was a challenge to my 50 year old eyes but it actuallt helped a lot so do not skip this - find a magnifying glass ;-)
+# [https://www.klipper3d.org/Rotation_Distance.html#calibrating-rotation_distance-on-extruders Calibrate Klipper extruder rotation_distance] - I skipped this because the test prints didn't show _any_ signs of over- or under-extrution.
+# [https://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide#Nozzle_Temperature Extruder nozzle temperature] - I skipped this because i already know what temperature the PLA i use need to be printed at on my E5+
 # [https://www.klipper3d.org/Pressure_Advance.html Pressure advance]: Calibrate extruder pressure.
-= Klipper + OctoPrint problems I ran into =
+= Problems I ran into =
-* OctoPrint reported errors in the Gcode that turned out beeing related to hidden ascii codes in the start_gcode. Solution was found somewhere on the Intarwebs i cannot recall...
+* The '''touch display on the printer does not work''' with Klipper and some search results suggests that the display on E5+ is not supported by Klipper :-/... i will keep look for solutions, but it is not essential to me because I use the OctoPrint webinterface. The stock 4.3 inch TFT LCD display is marked "DMT48270C043_06WT". Maybe that can help in the searce for solutions.
+  '''THIS FIXED THE DISPLAY -->''' https://www.reddit.com/r/ender5plus/comments/kx9hsy/klipper_screen_on_ender_5_plus/
-= Klipper + Moonraker + MainSail combo =
+* OctoPrint reported errors in the Gcode that turned out beeing related to hidden ascii codes in the start_gcode. Solution was found somewhere on the Intarwebs i cannot recall. I copied the Start and End G-code from Cura int Notepad++ and manually replaced all spaces with new ones. I could not see any difference on the spaces before and after BUT it worked so who cares ;-)
-will be addressed later ...
+* I lost http and ssh connection to the Raspberry Pi 3/4 into the Pressure Advance cube test print. The test print finished anyway so it was only network connections that died. I powercycled the Pi and everything seemed okay again!? It happened again and i suspect it is the WiFi connection that somehow locks up so I disabled the WiFi interface and connected the Raspberry Pi with an ethernet cable.
 = Reference pages =
+* My cry for help in the Danish Facebook group [https://www.facebook.com/groups/769445320232777/permalink/987651518412155/ Den seriøse Ender-3/Ender-5 gruppe]
 * [https://github.com/KevinOConnor/klipper Klipper] is a 3d-Printer firmware. It combines the power of a general purpose computer with one or more micro-controllers.
 * [https://github.com/OctoPrint/OctoPrint OctoPrint] provides a snappy web interface for controlling consumer 3D printers.
 * [https://github.com/arksine/moonraker Moonraker] is a Python 3 based web server that exposes APIs with which client applications may use to interact with Klipper.
-* [https://github.com/meteyou/mainsail Mainsail] lightweight & responsive web interface for the Klipper 3D printer firmware.
+* [https://github.com/meteyou/mainsail Mainsail] is a lightweight & responsive web interface for the Klipper 3D printer firmware.
+* [https://www.klipper3d.org/G-Codes.html This document] describe the G-Code commands that Klipper supports.
+* [https://github.com/KevinOConnor/klipper/blob/master/docs/Config_Reference.md Printer.cfg reference.]
+* My [[Printer.cfg]] file as of 5. jan. 2022
 = Notes for the future =
-* [https://www.klipper3d.org/Config_checks.html#calibrate-pid-settings Calibrating PID settings] is a wise thing to do everytime the environment around the printer changes 'significantly'.
+# During [https://www.klipper3d.org/Bed_Level.html#choose-the-appropriate-calibration-mechanism Probe calibration] it may be necessary to set the printer’s Z ''position_min'' to a negative number (eg, ''position_min = -2'').
+# [https://www.klipper3d.org/Manual_Level.html#adjusting-bed-leveling-screws Adjusting bed leveling screws] is nessesary to do now and then ;-)
+# [https://www.klipper3d.org/Config_checks.html#calibrate-pid-settings Calibrating PID settings] is a wise thing to do everytime the environment around the printer changes 'significantly'.
+# [https://www.klipper3d.org/Rotation_Distance.html#calibrating-rotation_distance-on-extruders Calibrate Klipper extruder rotation_distance].
+# [https://www.klipper3d.org/Pressure_Advance.html Pressure advance]: Calibrate extruder pressure. '''!!!''' Disable any PA setting already present in your config file '''before''' you run the PA test '''!!!'''
+# [https://www.klipper3d.org/Resonance_Compensation.html Resonance compensation]
+# ALWAYS slice as described in the [https://www.klipper3d.org/Slicers.html tips for configuring a “slicer” application for use with Klipper].

Ender 5 Plus + Klipper: Difference between revisions